Signal 23

Forum Tech Forums Car Audio & OEM Integration Forum How to install aftermarket sub and amp on A4 B8 (2011) ? 02-22-2011 07:23 PM #1 Registered Member One Ring How to install aftermarket sub and amp on A4 B8 (2011) ? - How do i do the wiring? Is there a writeup on this?- Hint about the power & ground?- Hint about Remote Turn on signal?- Hint about L/R signal to RCA converter?Thanks 02-23-2011 07:05 AM #2 Senior Member Two Rings I would like to know this too. A photo tutorial would be nice. for me 2010 AUDI A4 none B&O system 02-23-2011 01:04 PM #3 Active Member Two Rings Im currently installing a sub and amp, should be done by the end of the week. But the B8 section had some other install pictures. Also someone just did a B8 S4, with pictures but its on a B&O system. 2009 A4 3.2L V6 - Premium Plus - Ice Silver Metallic20" Vossen VFS1 + Hankook Ventus V12 Evo2 255/30ZR20 + Blesk 5000K HID Fogs + 35% Huper Optik Tint + LED Interior + LED LicenseAWE-Tuning 3.2L S-Flo Intake + AWE-Tuning A5 3.2L Touring ExhaustAdire Audio Brahma 15 + AudioQue AQ1200D + AudioControl LC2i 02-24-2011 07:17 AM #4 Active Member Two Rings Heres the thread for the B8 S4 install>Subwoofer-Installation-on-2010-S4Heres the thread from the B8 A4 section>B8-Aftermarket-Sound-System-PicturesJust threw in my sub and amp last night, couldnt do too much testing yet. Im using an AudioControl LC21 line converter. This also converter can provide the remote turn on signal. It sends the signal when is senses the speaker level input. So the way I have it setup uses only four wires connected to the car. Two wire for the speaker input and two wires for power.Amp- Audioque AQ1200DSub- Adire Audio Brahma 15Box-

The setup time from valid output data to the trailing edge of the ACK signal. © National Instruments Corporation 5-23 DIO 6533 User Manual... Page 83: Figure 5-20. Trailing-Edge Mode Input Unasserted Wait When REQ Asserted Initial State ACK Cleared * With REQ-edge latching enabled, the data read is from the last inactive-going REQ edge. DIO 6533 User Manual Programmable Delay Send Programmable Delay Clear Wait Figure 5-20. Trailing-Edge Mode Input... Page 84: Trailing-Edge Mode Timing Specifications ACK Cleared Programmable Delay Send Programmable Delay Clear Wait Figure 5-21. Trailing-Edge Mode Output 5-23 show the timing diagrams for trailing-edge 5-25 Chapter 5 Signal Timing Wait Data When 6533 Device Has Data to Output, Output Data* DIO 6533 User Manual... Page 85: Figure 5-22. Trailing-Edge Mode Input Timing Output Parameters ACK pulse width ACK inactive to next REQ inactive a*r* (min) = 225 + programmable delay (max) = 275 + programmable delay DIO 6533 User Manual t r*r t aa* t r*di t dir* t adi t dir Description All timing values are in nanoseconds. Page 86: Burst Mode Description All timing values are in nanoseconds. Figure 5-23. Trailing-Edge Mode Output Timing 5-27 Chapter 5 Signal Timing t a*r* t r*do(1) t r*do(2) Minimum Maximum — — — — — DIO 6533 User Manual... Page 87: Burst Mode Timing Specifications D2 is data point number 2, and so on. Figures 5-26 PCLK Data In DIO 6533 User Manual shows a burst mode transfer data input example, and shows a burst mode transfer

Us where did you see this ?2015-10-23Use props mavs88Second OfficerFlight distance : 8953215 ft>>>+ Add FriendPerson Message ItalyOffline 16#sploodge Posted at 2015-10-23 10:59Hi Mavs88, yeah, the process is the same for both A and B controllers..Thank you very much for this quick and clear answer!Now I hope it will work OK and that all will behave like a sweet, Nice, well-working combination of Phantom 3 Pro and remote controller.I also hope I will not loose signal, which happened to me 2 times during different flights.The latter at 40 meters distance...Phantom3 Pro - Apple iPad Air 2…Take care and thanks again!Max2015-10-23Use props mavs88Second OfficerFlight distance : 8953215 ft>>>+ Add FriendPerson Message ItalyOffline 17#sploodge Posted at 2015-10-23 10:59Hi Mavs88, yeah, the process is the same for both A and B controllers..Thank you very much for this quick and clear answer!Now I hope it will work OK and that all will behave like a sweet, Nice, well-working combination of Phantom 3 Pro and remote controller.I also hope I will not loose signal, which happened to me 2 times during different flights.The latter at 40 meters distance...Phantom3 Pro - Apple iPad Air 2…Take care and thanks again!Max2015-10-23Use props mavs88Second OfficerFlight distance : 8953215 ft>>>+ Add FriendPerson Message ItalyOffline 18#sploodge Posted at 2015-10-23 10:59Hi Mavs88, yeah, the process is the same for both A and B controllers..Mr. Sploodge,Thank you for your quick reply!I will update as soon as it'll be home and I hope that it will also not happen again that I loose video-signal,